Parallel groove clamp options can share the 16-240 mm² JB range while differing in listed materials and wire compatibility. This comparison focuses on conductor matching, bolt-pressure connection, and non-tension applications, helping you prepare the model, material, and line details needed for an accurate order.
Parallel Groove Clamp
HighPrecision Parallel Groove Clamp
Both options are electrical fittings for connections that do not bear tension. The standard clamp is used for splicing aluminum stranded wire or steel-core aluminum stranded wire, including steel stranded wire in overhead lightning protection lines. The HighPrecision model is intended for parallel splicing and jumper connections in overhead power and communication lines.
Picture a jumper connection at a non-linear tower: the conductors sit in parallel, and the fitting holds them through bolt pressure. Neither option is intended for a tension-bearing position. Confirm the line arrangement and mechanical load before ordering.
| Criterion | Parallel Groove Clamp | HighPrecision Parallel Groove Clamp |
|---|---|---|
| Main materials | Aluminum alloy or steel | Aluminum alloy, galvanized steel, or stainless steel |
| Compatible wires | Bare aluminum, aluminum alloy, copper, and steel-core aluminum stranded wire | Aluminum stranded wire, steel-core aluminum stranded wire, bare aluminum, copper, and aluminum alloy wire |
| JB type range | 16-240 mm² for the JB type example | 16-240 mm² for JB type |
| Connection and load | Parallel wire connection for non-tension positions | Parallel splicing or jumper connection for non-tension positions |
| Clamping method | Bolt-pressure clamping | Bolt clamping pressure |
| Installation approach | Place the wire in the slot and tighten the bolt without special tools | Place the wires in the slots and tighten the bolt without specialized tools |
The shared 16-240 mm² JB range gives both products a comparable starting point for small and medium cross-sections. The exact model still depends on the conductor size and connection. If one side uses a 70 mm² aluminum conductor and the other uses a different size, include both sizes in the inquiry.
Stainless steel appears among the material options for the HighPrecision model, together with aluminum alloy and galvanized steel. The standard clamp description identifies aluminum alloy or steel for the clamp body. This distinction matters when the fitting material is part of the purchasing decision.
Ask for the body and bolt material for the exact model, along with the conductor pairing required for the line. Keeping those details together helps match the selected material to the actual connection.
The options overlap on bare aluminum, copper, aluminum alloy, and steel-core aluminum conductors. The standard clamp also names steel stranded wire for overhead lightning protection lines. The HighPrecision version names aluminum stranded wire and steel-core aluminum stranded wire, then lists bare aluminum, copper, and aluminum alloy wires.
Write down the conductor material and cross-section for each side of the connection. Two fittings may share a nominal range while requiring different model confirmation for the conductor pairing. Include the conductor names, cross-sections, connection purpose, and whether the point is a jumper or lightning protection connection.
Both designs use a slot-and-bolt arrangement. Place the wire in the groove and secure it by tightening the bolt. Neither product requires specialized tools for this installation approach.
At an outdoor tower or line location, measure the access around the conductor layout. The installer needs room to place the conductors in the grooves and tighten the bolt. Since bolt pressure forms the connection in both products, identify the tightening information required for the exact model when placing the order.
Yes, the design is intended to connect two or more power wires arranged in parallel. That makes the number and arrangement of conductors an important part of model selection. Send a simple connection sketch with the conductor count, material, and cross-section when the fitting will join more than two wires.
Yes, the design can be adjusted to accommodate different wire specifications and cross-sections. Adjustment does not replace model selection: the conductor materials and cross-sections still determine the suitable fitting. Include the size of every conductor in a multi-wire connection so we can match the clamp to the actual arrangement.
Yes, the HighPrecision model is specified for overhead power lines and communication lines. Its connection type is parallel splicing or jumper connection, and its mechanical load is a non-tension-bearing position. State the line type and connection purpose so the intended application is clear in the quotation request.
Choose the Parallel Groove Clamp when its listed conductor types, aluminum alloy or steel body options, and non-tension connection use fit the project. Choose the HighPrecision version when its stainless steel material option or overhead power and communication line application fits the requirement. Send conductor materials, cross-sections, connection type, quantity, and required clamp material for a quotation.
The company
Handan Sanmao Electric Power Equipment Manufacturing Co., Ltd. was founded in 1996. It is an earlier and larger enterprise specializing in the production of power equipment and power fittings in Handan City. The company covers an area of approximately more than 23,000 square meters, and the factory building area is more than 12,000 square meters. The sales area and office building are more than 2,000 square meters.…
About Us ↗Visit company website ↗